Sveiki, skaitinejau forume, taciau nieko tinkamo neradau. Tikiuosi labai nenuszengsiu kurdamas nauja tema. Noriu jusu pagalbos. Tai va, pas mane pultelyje isseko baterijos, nupirkau naujas, sudejau, taciau neveikia. Beskaitydamas supratau, kad reikia pririst? Ar gali kas trumpai ir aiskiai pasakyti kaip tai padaryti? Buciau labai dekingas:)

Na pas mane tik vienas raktelis. O pas ji du.

jokios reakcijos, nebezinau jau ka ir daryti:)

Jei nezinot kaip tai atlikt tai geriau irbpatylekit... paspaudinet mygtukus matai... kai atsirisi abu ir galesi dziaugtis. Rasyk i pm jei dar reikia, paaiskinsiu

Sent from my GT-I9100 using Tapatalk 2

Jei nezinot kaip tai atlikt tai geriau irbpatylekit... paspaudinet mygtukus matai... kai atsirisi abu ir galesi dziaugtis. Rasyk i pm jei dar reikia, paaiskinsiu

Sent from my GT-I9100 using Tapatalk 2

Kokius abu atris, gudrociau tu, jei tik viena turi  Gal i pm ir pinigu iskarto atsiusti, kad cia negalima atsakymo suzinoti?
Temos autoriui. Pasiskaityk, pasidarysi. Nereiks I pm rasyti )) a6 raktas.pdf - 13 KB

cia raso zmones teisinga linkme.
bet oficialiai tai darosi taip:

paspaudi pultelyje lock arba unlock.
tada per 30s pasukant raktu uzrakini vairuotojo duris

Ir pultelis turetu atigauti. Cia galioja jeigu keitet baterijas arba visa diena be masinos spaudaliojot mygtukus.

..seip Ramaskinas teisinga info papostino jau

Tikriausiai pulteliui kazkas atsitiko, nes nereaguoja. Taciau bandant visokius variantus pabandziau ta su dviem rakteliais (turiu antra plastikini) ir maigant pulteli, istraukus is uzrakinimo spyneles (kol plastikiniu ijungtas degimas) jis reaguoja, t.y. sumirgsi avarinio zibintai, taciau nei atrakina nei uzrakina.

pirmiausia gal kai bandei pririsinet jau isnaudojai visas laisvas vietas kiek gali irasyt rakteliu uz tai ir neveikia pririsimas. pagal aprasyma kisi rakta (plastikini -servisini) i spynele, pasuki degima, is lauko su kitu raktu uzrakini mechaniskai duris ir spaudi atrakinimo knopke 5 kartus. tada nusinulina priristu rakteliu atmintis.
po istrynimo vel kartoji rakto pririsimo procedura (vienas paspaudimas - pirma vieta atminty, 2 paspaudimai - antra vieta ir t.t.) paskui kai jau atlieki pririsima, isjungi degima ir istrauki rakteli is spyneles ir tik tada bandyk rakinet centrini. kitaip centrinio nevaldysi kol raktelis bus spynelej degimo

Junk kompa ir pririsi. Zaidi cia be reikalo tik.

taip, eitu.

Self-diagnosis of central locking system
Matching or deleting vehicle key for radio remote control
The vehicle is supplied with two remote keys.

If new or additional ignition keys are required they must be matched/adapted to central locking control unit -J429.

The vehicle keys must also be adapted to immobiliser control electronics.

=> Electrical System; Repair group 01; Immobiliser Self-diagnosis

If one of the faults 00955 to 00958 is displayed, the keys must be re-matched =>Page 01-127.

Methods of matching remote keys:

◆ To match remote keys without a second key, the procedure is described further in adaption under channel 21. Matching of remote keys via adaption =>Page 01-130.
◆ To match remote keys by using a second key, follow the following steps.
Matching procedure for new remote keys

‒ Unlock the vehicle from the outside via the driver's door lock
‒ Switch on the ignition (using additional key).
‒ Check in measured value block 007 display zone 3 how many keys have already been matched =>Page 01-120.
 
 
→ Indicated on display: Read measured value block        7    ⇒
    0    0000    1100
 
Display zone 3 shows how many remote keys have been matched and in which memory positions (2x in positions 1 and 2 in example shown).

‒ Lock vehicle from outside with the key to be adapted by way of the driver's lock door.
‒ Within 5 seconds press "unlock" key of remote key until next memory position is reached (3x in example).
Each time the button is pressed the hazard lights will flash to confirm.
‒ Wait 5 seconds.
‒ Then press "unlock" key again. This unlocks the vehicle =>key has been successfully matched.
‒ Switch off ignition and remove ignition key.
‒ Check function of new remote key.
‒ Check display zone 3 in measured value block 007 => Page 01-120.
 
 
→ Indicated on display: Read measured value block        7    ⇒
    0    0000    1110
 
How many remote keys have been matched and in which memory positions is displayed in display zone 3. It must now display a further "1" (in example: 1110).

Notes:

◆ Make sure new keys are always matched to vacant memory positions. If use is made of occupied memory positions (can be seen from "1") the remote key already matched for this memory position will no longer function.
◆ A successful adaption can be determined by reading measured value block (function 08), display group number 007 =>Page 01-120.
◆ A maximum of four keys can be matched.
◆ The matching process must be completed within 30 seconds. If 30 seconds are exceeded the process must be repeated.
Re-matching procedure for existing remote keys

Note:

This procedure must be performed after changing the batteries in remote keys, or if the fault reader displays fault codes 00955 to 00958.

‒ Press key on remote key.
If vehicle is neither locked nor unlocked:

‒ Lock and unlock vehicle within 30 seconds by way of driver's door lock.
‒ Then check function of re-matched remote key.
If vehicle is still not locked or unlocked, key must be re-matched. Match radio remote control vehicle keys =>Page 01-124

Deleting memory addresses

It is possible to erase memory positions, if, for example, a customer has lost a radio remote control key.

‒ Switch on the ignition using a key.
‒ Lock vehicle from outside with the key to be adapted by way of the driver's lock door.
‒ Press "open/unlock" button on radio remote control key five times at 1 second intervals.
Note:

Each time the button is pressed the hazard lights will flash to confirm.

‒ Switch off ignition and remove ignition key.
‒ Memory positions are erased; it must not be possible to unlock central locking system by pressing "remote opening" button.
‒ Check display zone 3 in measured value block 007 =>Page 01-120. All memory positions must now be erased and reset to "0" (in example: 0000).
‒ Up to four keys can now be re-matched once again.
 

kad ir pats gali

Sveiki,nu ir man cia tokie cirkai nutiko  zodziu ...
turiu 2 orginalius raktus,1 baterija pakeitus,neveikia pultelis (centrinnis ir signalizacija to pultelio,kurio baterija keitesi)
taciau jaigu ijungiu su veikianciu raktu degima,o su neveikianciu is lauko puses mechaniskai uzrakinu duris,poto paspaudus atrakinimo knopke 1 karta (avarinis sumirksi),po penkiu sek antra karta,raktelis prisirisa,kaip ir viskas ok,TACIAU 
tas raktas kuris neveike prisirisa,viskas ok,bet kitas su kuriuo buvo degimas ijungtas,nebeveikia,susikeicia zodziu vietomis 
zodziu neina padaryt,kad abudu raktai veiktu kaip buvo veikia 
kame beda ?gal kazka netaip darau ? gal kas buvote susidure,eisiu bandyt dar pazaist su 1 raktu is lauko puses ...